Just how do you really feel about Tools You Need to Install a New Bathtub ?
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is conveniently accessible, the task can move speedily; if you need to open a wall surface to eliminate the old tub as well as place the brand-new bathtub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have actually certified yourself for the task and are comfortable trying it. Rather than employing a service provider to take control of a halfway-completed project, it is much better to consider utilizing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This short article will certainly aid you install a new bath tub in your washroom if you have already gotten a brand-new bathtub and don't need to transform the setup of your previous water supply pipes.
Your tools as well as product list should comprise the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bath must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited access that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, place the bathtub in the called for placement. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water system and also inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet and also the normal outlet for leaks.
Finally, repair the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has been utilized a minimum of once as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area between the tap and also the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The former kind needs to be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath and the tiling, bring about issues with dampness and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and also installations. They are marketed in tubes as well as cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader on How to Install a Bathtub, I think sharing that piece of content was appropriate. Do you know anybody else who is enthusiastic about the niche? Take a moment to promote it. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Learn More